-
1. Lock the product, the container, and the speed before anyone quotes you
-
2. Plan the whole line, not the filler
-
3. Match the machine to the liquid
-
4. Calculate TCO, not the quote
-
5. Verify the supplier's boundaries
-
6. Stress-test the automation
-
7. Put the acceptance criteria in the contract
-
Common mistakes worth watching for
I've been the procurement manager at a mid-size beverage equipment integrator for six years. My annual bottling line equipment budget runs around $1.4 million, and I've negotiated with more than twenty vendors in that time — honey producers in the Midwest, a couple of small wineries on the West Coast, and two brewery clients running automated lines. Every order hits the same spreadsheet, the same question set, the same seven steps.
This checklist is for anyone sourcing a bottling line, whether it's a 400-BPH honey line or a 6,000-BPH automated beer line. Same sequence, different numbers. Seven steps, four to six weeks of actual work. If you run them in order, you avoid the two most expensive mistakes I see: buying equipment that doesn't fit the product, and signing a line whose true cost is 20-30% above the quoted price.
1. Lock the product, the container, and the speed before anyone quotes you
The first step has nothing to do with vendors. Before I send a single RFQ, I write a one-page spec: product viscosity, particulate size (honey with comb fragments is not the same as clear wine), bottle material and weight, closure type, label format, target bottles per hour, and shift pattern. I send that PDF in the email subject line, not the body. Vendors quote what you put in front of them — sometimes nothing else.
The question buyers usually ask is "how much for a bottling line?" The question they should ask is "what's the stable, sustained fill rate per hour, on this bottle, with this product?" Those two numbers can differ by 30-40%, and only one of them is the one you're actually buying.
Checkpoint: a one-page spec with the bottle drawing, closure spec, target BPH, and product sample photos, sent to every supplier before any call.
2. Plan the whole line, not the filler
This is where budgets quietly break. A bottling line isn't a filling machine — it's a rinser, filler, capper or corker, labeler, case packer, conveyor system, CIP skid, and whatever accumulates bottles between them. Most buyers focus on the filler price and completely miss the end-of-line, which is often 40-50% of total line cost.
My rule: I list every station on a single sheet, mark it Must or Optional, and only then ask for quotes. Optional stations become "phased later" line items in the budget — not surprises in Month 7.
Checkpoint: one sheet per station. Every row has a Must/Optional flag and a rough cost range. If a vendor quotes a line without an itemized station list, I don't compare it — I ask back for the breakdown.
3. Match the machine to the liquid
Honey, wine, and beer are not interchangeable on the same filler, and any supplier who suggests otherwise is either generalizing or hasn't done your product.
- Honey bottling lines deal with viscosity, crystallization, and heat. If you're filling raw or lightly filtered honey, you need jacketed heated tanks, heated lines, and a filler with a slow, controlled dispense — not a high-speed gravity filler.
- Wine bottling lines deal with oxygen pickup. That usually means gravity or vacuum fill heads, minimal product return, and corking or screw-cap stations sized for your closure. A line that treats wine like a beverage is a line that oxidizes it.
- Beer bottling lines deal with CO2. Counter-pressure filling, CO2 purging, and dissolved-oxygen control aren't optional. If a quote doesn't mention all three, that's not a beer line.
I've seen quotes where the same filler head got pitched to a honey producer and a winery. The honey operation ended up with a hot-fill filler that scorched the product; the winery got a filler with too much product return and lost a batch to oxidation. Neither was a scam — both were the wrong tool.
Checkpoint: ask the supplier for two named reference installations in your exact product category — honey, wine, or beer — and call those references. Not a list of logos. Two phone numbers.
4. Calculate TCO, not the quote
The quoted price is usually 65-75% of the real cost of getting a line running. The rest — don't hold me to the exact split, it shifts line to line — sits in installation, commissioning, utilities (steam, compressed air, power, water), operator training, spare-parts stocking, and out-of-warranty service contracts.
The Vendor B incident in 2023 changed how I budget bottling lines. I had three quotes for a mid-size wine line. Vendor A quoted $310,000. Vendor B quoted $268,000 — 14% lower. I nearly signed with B. Then I built the five-year TCO in Excel: B charged separately for installation ($14,000), commissioning ($8,500), operator training ($4,000), and a first-year spare-parts kit ($11,200). B's number was also quoted ex-works, so freight added $9,500. Five-year total: roughly $332,000 for B vs. $315,200 for A. The "cheaper" quote was 5% more expensive before I even added electricity — B's filler drew about 22% more kWh — and B's out-of-warranty service rate was 30% higher.
That comparison is why my procurement policy now requires a full TCO sheet, not just a quote, for any line over $50,000.
Checkpoint: a TCO sheet with rows for equipment, freight, installation, commissioning, utilities (one-year estimate), spare parts (year one), training, and a five-year service assumption. If the vendor won't give you the utilities and service numbers, use your own and label them estimated.
5. Verify the supplier's boundaries
Here's something vendors won't volunteer: most "one-stop" bottling line suppliers are integrators, not manufacturers. They might build the filler in-house, source the labeler from a partner, and subcontract the case packer. That's fine — but you need to know which is which, because warranty responsibility splits along those lines.
What most people don't realize is that the supplier who says "we don't make the labeler — these two companies do, and here's who I'd use for your line" is usually more reliable than the one claiming they make all of it. I've had a supplier tell me point-blank they weren't the right fit for an automated beer line and recommend a competitor for that part of the scope. I bought the honey line from them anyway, because that honesty told me exactly where their competence ended — and where it didn't.
Checkpoint: ask, in writing, "Which stations do you manufacture, which do you integrate, and who holds the warranty for each?" Get the answer in a paragraph, not a spec sheet.
6. Stress-test the automation
"Automated bottling line" is a marketing phrase until you ask it to do something specific. Three questions separate a real automation spec from a sales deck: how many operators per shift does your OEE assumption require? What's the changeover time between SKUs, measured in minutes, door to door? What are the top three failure modes, and what's the mean time to recovery for each?
When I compared a fully automated line's intervention log against a semi-automatic line running the same product, I finally understood what automation actually buys you. The manual line needed two operators per shift; the automated line needed one, plus a maintenance tech who responded to faults. The labor savings were real but smaller than the sales deck suggested, and the skill profile shifted from operators to technicians. That's not a bad trade — it's just a different trade than the one the brochure is selling.
Checkpoint: ask for a one-page automation spec with the OEE assumption, changeover time, required operator count, and top three failure modes. If it doesn't exist, the "automation" is a feature list.
7. Put the acceptance criteria in the contract
Most buyers skip this step, and it's the one that saves you when the line runs at 70% of rated speed on your actual product.
The contract needs written FAT (factory acceptance test) and SAT (site acceptance test) criteria: bottles per hour at a stated efficiency, reject rate, downtime allowance, and — critically — the exact product and bottle used for the test. Not "line shall perform according to specification." I've watched that clause resolve exactly zero disputes. Written numbers, product to be tested, and a defined remedy if the test misses.
Checkpoint: one paragraph in the contract stating the FAT/SAT target numbers, the exact product used in the test, and what happens if the line misses the target.
Common mistakes worth watching for
These are the ones I've made or watched a colleague make:
- Quoting the filler first. The filler is maybe 30-40% of the line. Price the whole line before you feel good about a number.
- Not defining the spec before the RFQ. Every vendor quotes a different interpretation. You'll compare apples to oranges and pick whichever apple looks cheaper.
- Assuming automation means fewer people. It usually means different people, with different skills, arriving at a slower cadence.
- Skipping acceptance criteria. Verbal performance promises are worth exactly what they cost.
- Trusting "we do everything." Ask what they outsource. If the answer is "nothing," they're either a genuine full-range manufacturer or they're simplifying for you.
One timing note: the cost and lead-time figures I'm using here are from my Q4 2024 TCO sheets. Stainless steel, freight, and component pricing moved a lot through 2022-2023, and the market is still uneven. Verify current pricing before you budget — this isn't a fixed table, and it shouldn't be treated like one.
The checklist works because it's a bit boring. The order matters more than the spreadsheet does: product first, line second, supplier third, price fourth. Most sourcing problems I've seen come from running those in reverse.